Sonex -- The Sport Aircraft Reality Check!
 

SONEX
WAIEX
XENOS
ONEX
AeroVee
AeroConversions Accessories


Postal:
Sonex Aircraft, LLC
P.O. Box 2521
Oshkosh, WI 54903

Shipping:
Sonex Aircraft, LLC
511 Aviation Road
Oshkosh, WI 54902

E-Mail:
Sales & Information
Orders
Billing Questions
Tech Support
Shipping/Freight

Phone:
920-231-8297

Tech Support:
920-230-TECH
Hours: M,W,F
10am-Noon &
2pm-4pm CST

Fax:
920-426-8333

Visit Us:
Map to Factory, Lodging, Restaurants, & Local Attractions

Sonex Aircraft
Terms and Conditions
Drawing Revisions: Sonex
Subscribe to the Sonex Aircraft
Technical Updates Mailing List

There are two types of Revisions made to Sonex Aircraft Plans: Required Revisions and Optional Revisions. Builders should check this page periodically for new revisions.

Required Revisions:
These are revisions that have a direct impact on the construction process. It is very important you make these revisions to your plans immediately.

Optional Revisions:
These are revisions that are mainly drawing clean-up and note changes. They do not directly impact the construction process.

Note: Some of these revisions may already be made on your plans, depending upon when your plan set was printed. The Revision Block on each page of your plans details revisions already reflected in your set of plans. For an example revision block and explanation of its use, download the sample plan sheet (PDF)*.

Reporting Errors:
Please notify Sonex Aircraft, LLC of any drawing errors at: 920-230-TECH (8324) or by e-mail at:
tech@sonexaircraft.com

*Download Adobe Acrobat Reader to view Sonex PDF files.

In order to simplify revision log listings, each Sonex Aircraft design has it's own Revision Log page:

Back to Revision Log Index

Waiex Revision Log

Xenos Revision Log

Onex Revision Log

Sonex Revisions

Required Sonex Revision Log: Last Updated August 24, 2011

Date

 Drawing Rev Location Incorrect Correct
6.8.01 SNX-B06 --
Page 30
 Maneuvering Speed: 136 MPH Maneuvering Speed (Va): 125 MPH
6.8.01 SNX-C03 B
Detail -05
 3/4"D x 0.035" Wall 4130 12 3/4" Long 3/4"D x 0.035" Wall 4130 14 3/8" Long
7.14.09 SNX-C06 NC Detail -06 Make from SNX-Z02-03 Angle Stock

Make from 1" x 1" x 1/8" 6061-T6 extrusion.

Note: the depiction is correct but the material call-out is incorrect.
7.12.99 SNX-F17 NC Detail -03 "B" Distances in Coordinate Table Add 1-3/4" (44.5mm) to each "B" dimension.
6.8.01 SNX-F26 A,B
-03R/-03L
 Right Hand Lower Longeron (shown) Left Hand Lower Longeron (shown on Bottom View)
Right Hand Lower Longeron (shown on Side View)
6.28.11 SNX-L01 NC Detail A and -02 Tri Gear Installation AN4C-17 Bolt and AN365-428 Nut Replace with AN4-17 Bolt, AN310-4 Castle Nut, and MS24665-208 Cotter Pin
6.28.11 SNX-L01 NC -01 Standard Gear Installation AN4C-30 Bolt and AN365-428 Nut Replace with AN4-30 Bolt, AN310-4 Castle Nut, and MS24665-208 Cotter Pin
10.26.01 SNX-L03 --
Detail -01 Caster/Push Rod
 MS20392-3C9 Clevis Pin , 1 Req'd

AN23-10 Clevis Bolt, 1 Req'd
Add AN310-3 , 1 Req'd
10.26.01 SNX-L03 --
Detail -01 Rudder Horn/Push Rod
 MS20392-3C9 Clevis Pin , 1 Req'd AN23-12 Clevis Bolt, 1 Req'd
Add AN310-3, 1 Req'd
6.28.11 SNX-L03 A -01 Tail Wheel Installation AN4C-12 Bolt and AN365-428 Nut Replace with AN4-12 Bolt, AN310-4 Castle Nut, and MS24665-208 Cotter Pin
12.10.03 SNX-P20 --
Detail -04 Fin Installation
--
 Add Fin to 3300 Tri-Gear Wheel Pant per this drawing: SNXP20b.pdf
Add AN310-3, 1 Req'd
8.24.11 SNX-P22 A -09 and -10 Engine Mounts --

Added -07 Additional Lower Cross Tube. See Service Bulletin SNX-SB-007: SNX-SB-007-TRI-3300_Motor_Mount_Change.pdf

Jabiru 3300 Tri Gear Motor Mount Tube Installation instruction sheet: Jab_3300_Mount_Tube_Installation.pdf
6.8.01 SNX-T02 --
Section E-E
 CCP-42 50 req'd CCP-42 52 req'd
12.6.04 SNX-W12 C
-02R/L, -03R/L
--
 Add note for kit builders: Pilot holes for rib attach points must be drilled accurately. Use a formed rib as a pattern.
6.8.01 SNX-W13 --
Detail -02R
 5/8" [15.58 mm] 5/8" [15.88 mm]

 

Optional Sonex Revision Log: Last Updated July 13, 2011

Sport Trainer (ST) Modification for your Dual-Stick Equipped Sonex or Waiex (12.04.09):
SNX-C08_OptionalCenterControls_A.pdf
SNX-C09_OptionalCenterDetails_A.pdf
General Warning: (2.12.07) Do not install the ST modifications until the wing is installed in the wing spar box.

Lowered Seat Modification for Dual-Stick Sonex:
These drawings detail the optional lowered seat installation. These drawing have been included in all complete plans sets since November 2008.
SNX-C06-LowSeat.pdf
SNX-C07-LowSeat-LowCabin.pdf

Date

 Drawing Rev Location Incorrect Correct
10.31.07 SNX-B03 NC SNX-B10 and SNX-B11 drawings. -- Remove from Drawing Tree. These documents are supplemental manuals, not included in the Sonex plans, that ship with your AeroVee or Jabiru engine purchase from Sonex Aircraft, LLC.
11.12.08 SNX-B03 G Drawings SNX-C06, SNX-C07, SNX-C08, SNX-C09, SNX-W24, SNX-W25, SNX-W26, SNX-W27. -- Updated Drawing Tree to show Lowered Seat Modification, Sport Trainer (ST) Modification, and Sport Acro Modification.
3.24.11 SNX-B03 H SNX-T14 SNX-T14 Optional Tail Tip Installation SNX-T14 Tail Tip Installation
12.6.04 SNX-B10 NC
Page 3 "Oil Cooler Installation"
 MS20822-6D MS20822-6-6D
12.6.04 SNX-B10 NC
Page 3 "Oil Cooler Installation"
 799-610020 Qty 2 799-610020 Qty 3
12.6.04 SNX-B10 NC
Page 3 "Oil Cooler Installation"
 799-613160 Qty 2 799-613160 Qty 1
12.6.04 SNX-B10 NC
Page 3 "Fuel System Installation"
 AN816-6D Qty 2

AN816-6D Qty 1
12.6.04 SNX-B10 NC
Page 3 "Fuel System Installation"
--
 Add AN816-6-2D Qty 1
12.6.04 SNX-B10 NC
Page 3 "Cockpit Controls"
--
 Add Rod End for Throttle Cable
12.6.04 SNX-B10 NC
Page 4 "Wicks"
 MS20822-6D MS20822-6-6D
12.6.04 SNX-B10 NC
Page 4 "Wicks"
--
 Add AN816-6-2D Qty 1
12.6.04 SNX-B10 NC
Page 4 "Wicks"
 AN816-6D Qty 4 AN816-6D Qty 3
12.6.04 SNX-B10 NC
Page 4 "Jegs"
 799-610020 Qty 3 799-610020 Qty 4
12.6.04 SNX-B10 NC
Page 10
--
 Added use of Locktite 243 to Step #2
12.6.04 SNX-B10 NC
Page 13
 Do not cut Baffles for 2200 per these dimensions Cut Baffles leaving 1" extra material. Trim as required to fit.
10.10.07 SNX-B10 D Oil Cooler Installation, pages 3, 4, and 12 Leave Blank Jabiru Engines with hydraulic lifters must use an AeroClassic 800075 Oil Cooler to avoid interference with the exhaust system.
12.1.03 SNX-B04 A
TAIL VIEW
--
 Option: Add Rudder Trim Tab- VW Lower RH 1.5"Wx6" L
Option: Jabiru Lower LH 1.5"W x 6"L. Bend tab out as req'd
2.12.07 SNX-C01 B -01 Installation Flap Drive Pivot Blocks installed with AN4 Bolts Install Flap Drive Pivot Blocks with AN3 Bolts and associated hardware.
12.1.03 SNX-C02 D
-03R/-03L
--
 Add length as req'd to reach rudder horn.
2.12.07 SNX-C02 E -04 Push Rod Assembly Compression Spring, 2 Required on -04 Assigned Part Number SNX-C02-10 to this Spring
2.16.09 SNX-C02 E -04 Push Rod Assembly -- Note: An Aurora MW-5 Rod End Bearing with a 3/16" I.D. x 5/16" O.D. x 3/8" Long Sintered Bronze Bushing (SYMMCO # SS-610-6 or equal) to bush down to 3/16" inside diameter may be substituted for the MW-3M-16
12.1.03 SNX-C05 C
-01 Dual Stick Assembly
 AN3-14 Bolt 2 Req'd AN3-5 Bolt 2 Req'd
11.12.08 SNX-C06 NC -- -- Lowered Seat Modification Drawing Created: SNX-C06-LowSeat.pdf
1.10.11 SNX-C06 NC Detail H-H -11 Control Pushrod Cover Reference -08 Control Pushrod Cover Reference
1.10.11 SNX-C06 NC -06 Angle Make from SNX-Z02-03 Make from 1/8"x1" 6061-T6 Aluminum Angle Extrusion
1.10.11 SNX-C06 NC Section H-H -- Corrected Quantity of hardware needed from 8 to 6, and from 16 to 12.
11.12.08 SNX-C07 NC -- -- Lowered Seat Modification Drawing Created: SNX-C07-LowSeat-LowCabin.pdf
1.10.11 SNX-C07 NC -02 Assembly Callout for SNX-F10-02 Angle Callout for SNX-C06-05 Angle
1.10.11 SNX-C07 NC View A-A, View C-C, and Construction Order Callout for SNX-F10-02 Angle Callout for SNX-C06-05 Angle
11.12.08 SNX-C08 NC -- -- Sport Trainer (ST) Modification for Dual Stick Sonex or Waiex: SNX-C08_OptionalCenterControls_NC.pdf General Warning: Do not install the ST modifications until the wing is installed in the wing spar box.
12.04.09 SNX-C08 A -- --

Sport Trainer (ST) Modification for Dual Stick Sonex or Waiex: SNX-C08_OptionalCenterControls_A.pdf

Replaced C09-11 Flap and Brake Mount with CO9-19 Flap and Brake Mount and C09-10 Support Angle with C09-20 Support Angle
Note: C09-11 is still acceptable installed per Rev N/C.
11.12.08 SNX-C09 NC -- -- Sport Trainer (ST) Modification for Dual Stick Sonex or Waiex: SNX-C09_OptionalCenterDetails_NC.pdf General Warning: Do not install the ST modifications until the wing is installed in the wing spar box.
12.04.09 SNX-C09 A -- --

Sport Trainer (ST) Modification for Dual Stick Sonex or Waiex: SNX-C09_OptionalCenterControls_A.pdf

Replaced C09-11 Flap and Brake Mount with CO9-19 Flap and Brake Mount and C09-10 Support Angle with C09-20 Support Angle
Note: C09-11 is still acceptable installed per Rev N/C.
12.2.02 SNX-D01 A
Section D-D
--
 Add AN365-832A Nut, 5 Req'd on -02
12.2.02 SNX-D01 A
-04 hook rail assy
--
 Add AN365-832A Nut, 2 Req'd on -04
12.1.03 SNX-D01 B
-01 Canopy Install
--
 Add Machine Screw option to attaching side rails
2.12.07 SNX-D01 C Detail R -- CANOPY LOCK PIN IS OF CRITICAL IMPORTANCE! This Lock Pin MUST be installed for all flights.
12.1.03 SNX-D02 B
Detail -03
 55 1/8" Long 56 7/8" Long
12.6.04 SNX-D02 C
Detail -20
--
 Swedged Canopy Cable available from Sonex Aircraft, LLC
12.1.03 SNX-E01 NC
Electrial Wiring Diagram
 8 gauge wire routed from Main Bus to Alternator Route 8 gauge from Alternator directly to Battery
12.1.03 SNX-E01 NC
Electrial Wiring Diagram
 4 gauge wire routed from starter to relay 20 gauge wire
12.1.03 SNX-E01 NC
Rev A Drawing Released
--
 Current Stratomaster and Optional Lighting Wiring Diagram.
Download new drawing: SNX-E01a.pdf (Link expired in-favor of SNX-E01B below).
3.23.11 SNX-E01 A -- -- Revised schematic to eliminate wiring for specific equipment. Added panel size and depth details to aide panel planning. Download new drawing: SNX-E01B.pdf
12.1.03 SNX-F01 A
Detail B
 Drill, Countersink: CCP-44 Dril, Countersink: CCC-44
7.15.09 SNX-F02 NC Section E-E -- Added note to pilot drill wing mounting holes from 1/4" to 3/8" Dia. using
3/8" piloted drill bit with dulled 1/4" pilot.
Added note that three center holes in spars are tooling holes and will have
NO hardware installed when aircraft is complete.
2.15.11 SNX-F02 A Construction Order -- Added Step 16, "Drill 1/4" through Rear Spar Carry Through Assembly"
3.31.00 SNX-F03 NC -01 Assembly AN3-10A Bolts AN3-7A Bolts
7.15.09 SNX-F03 A -02 Channel -- Added 1-3/4" hole location for drop seat option.
2.4.11 SNX-F03 B Details -02, -03, -05L, -05R, and -01 Assembly 1/4" Diameter Holes 3/16" Diameter Holes
12.2.02 SNX-F10 NC
Detail -19
 AN3-10A Bolts AN3-7A Bolts
2.12.07 SNX-F10 A Detail -03 (SNX-SB-003) Make from SNX-Z02-03 Angle Stock Make from 1"x1"x1/8" thick 6061-T6 Angle
12.6.04 SNX-F11 B
View N-N
 F16-12 Aft Clip F17-12 Aft Clip
2.12.07 SNX-F11 B Detail S Callout for AN470AD-4-5 IS NOT AN ERROR Install Rivet so Factory Head is in the cockpit. Rivet is driven into the c'sink inside the spar box.
12.1.03 SNX-F13 NC
-03 R/L
--
 Add 3/16" Hole Call-out to side view
9.28.09 SNX-F13 NC Detail -01 Missing dimension for upper, forward-most 11/64" dia. hole Missing dimension is 11/16"
9.14.10 SNX-F13 A Details -01, -07, Detail A -- Deleted -07 Vent Door, Detail A, and Vent depiction in Detail -01
9.14.10 SNX-F13 A -02R and -02L -- Clarified slots are in -02L ONLY
12.1.03 SNX-F14 C
-08R/L
 Incorrect Side View Extend side view to match front view
12.1.03 SNX-F14 C
-13R/-13L
 7 Spaces @ 15/16" 5 Spaces @ 15/16"
9.14.10 SNX-F14 D Detail -13R End view incorrect Moved end view from LH side to RH side
9.14.10 SNX-F15 NC Detail -13 -- Vent Door Latch Deleted.
12.2.02 SNX-F16 C
Detail -02
 3/16" Dimension Line is shifted to the right.
--
12.2.02 SNX-F16 C
Detail -02
 Top View doesn't show 1/4" x 1" cutout
--
9.14.10 SNX-F16 D Detail -03 -- Added note about additional fasteners added to assembly depending on gear configuration. Reference SNX-F01.
2.6.09 SNX-F17 NC Detail -02 -- Drawing is correct. Adjust flutes in firewall as needed to install Southco fasteners. See photo: Southcos-Installed.jpg
9.14.10 SNX-F19 NC Detail C Drawing Correction Removed depiction of 2 screws installed on later assembly.
9.14.10 SNX-F20 NC Detail -05 -- Lengthened lower flange from 21/32" to 25/32" to provide more leeway during installation.
12.2.02 SNX-F21 B
Section K-K
 F22-02 Bulkhead F23-02 Bulkhead
2.12.07 SNX-F21 B Section K-K Locate per Pilot Holes in Bulkhead Locate per Pilot Holes in the lower angle
2.12.07 SNX-F21 B Detail D Cherry CCP-42 Blind Rivets 8 req'd on -01 Cherry CCP-44 Blind Rivets 8 req'd on -01
9.14.10 SNX-F21 B Detail -01 -- Added note to rivet lower skin only after wings and tail are rigged.
9.14.10 SNX-F21 B Section N-N -- Added dimensions to locate SNX-F23-11 at 8-7/8" for lowered seat option.
9.14.10 SNX-F21 B Section P-P -- Added dimensions to locate SNX-F23-09 at 16-9/32" for lowered seat option.
5.27.99 SNX-F22 NC Detail -06 3 spaces at 1" CTC 3 spaces at 5/8" CTC
5.11.11 SNX-F22 A Detail -03 Missing the dimension from left edge of part to the first of 8
holes.		 Added 2-27/32" dimension.
12.1.03 SNX-F23 NC
-08 Fitting
--
 Add 1/2" to Tab on fitting to allow for easier Seat Belt attach.
12.6.04 SNX-F23 A
Detail -12 Aft Support Channel
 -12 Support Angle -13 Support Angle
6.26.08 SNX-F23 B -10 Channel and -12 Channel 1" diameter hole 1-1/8" Diameter hole
6.26.08 SNX-F23 B -09 Assembly and -11 Assembly 1"OD x 7/8 ID Plastic Bushing 1-1/8" OD x 7/8" ID Plastic Bushing (Heyco 2163 or equivalent)
9.14.10 SNX-F24 NC Detail -01 -- Increase size of note to keep cross tie box square, not twisted.
12.6.04 SNX-F25 NC
Detail P
 SNX-F26-05R, -05L SNX-F26-07R, -07L
12.18.09 SNX-F25 D -01L and -01R -- Use CCP-46 rivets instead of CCC-46 rivets to attach F26-08 Rudder Stop
Plates.
12.1.03 SNX-F27 B
-09 Fairlead Assembly
 -07 Fairlead Mount Weldment -10 Fairlead Mount Block
6.10.01 SNX-G01 NC -03 and -04 Fuel Tank Straps -03 and -04 Fuel Tank Straps Made fuel straps two pieces. Deleted part numbers -03 and -04 and replaced with -08 (Qty 2) and -09 (Qty 2). Note: SNX-G01-10 universal Fuel Tank Straps now provided with kits.
11.21.03 SNX-G01 A -05 Tank Assembly, View A-A, Fuel System Schematic -- Revised to show Electronic Fuel Level Probe (Sight gauge shown as optional).
12.6.04 SNX-G01 B
-05 Tank Install
 1/8" Felt Strips Note: Felt Strips optional with Sonex RM (plastic) fuel tank.
2.12.07 SNX-G01 B Detail -08 and -09 Straps -- Note: Straps may be substituted with 3/4" wide x 0.125" thick 6061-T6 Aluminum. Note: SNX-G01-10 universal Fuel Tank Straps now provided with kits.
9.3.09 SNX-G01 C -05 Tank Assembly 1/4" Pipe Thread Brass Close Union (Automotive) AN911-2D Nipple
2.12.07 SNX-G02 NC General Notes -- Add Note: Rotationally Molded Tank Standard. Aluminum tank option shown
12.6.04 SNX-L01 NC
-09 Assembly
--
 Note: Optional Machined Brake Drum: ACV-W01-10 may be substituted for the Azusa Brake Drum.
2.12.07 SNX-L01 NC -05 Axle Do not drill 5/32" Cotter Pin Hole located 1 1/8" from end Drill this 5/32" Hole and locate once wheel and brake assembly are installed
7.13.11 SNX-L01 A -- Note: Do not allow cad plated tools or hardware to contact
titanium gear legs.		 Removed note.
2.12.07 SNX-L02 NC -01 Installation Helical Compression Spring, 1 Required on -01 Assigned Part Number SNX-L02-12 to this Spring
3.28.07 SNX-L02 NC -08 Axle Bushing Some kit-supplied bushings are 4.5" long. Trim bushing to 4.25" long.
10.4.07 SNX-L02 NC Detail -08
--
 Bushing SNX-L02-08 Supplied in kits may be 1/4" too long. Trim bushing to fit.
10.29.01 SNX-L03 NC -01 Tail Wheel MS20392-3C9 and MS20392-3C11 Clevis Pins Replaced with AN23-10 and AN23-11 Clevis Bolt and AN310-3 Castle
Nuts.
7.11.11 SNX-L03 A -- Note: Do not allow cad plated tools or hardware to contact
titanium gear legs.		 Removed note
7.11.11 SNX-L03 A -01 Tail Wheel Install AN4C-12A Bolt (Qty. 2) AB365-428 Nut (Qty. 2) AN4-12 Bolt (Qty. 2), AN310-4 Castle Nut (Qty. 2) and MS24665-208
Cotter Pin (Qty. 2)
7.11.11 SNX-L03 A Detail -05 Width of Caster Opening 3/4" should be 13/16". 1-1/2" should be 1-5/8"
7.11.11 SNX-L03 B Detail -05 -- Drive plate thickness increased from .090 to .125" for universal
application on Onex.
12.1.03 SNX-L04 A
Detail E
--
 Optional: Replace AN525-416R28 with AN4-16A Bolts.
12.1.03 SNX-P01 NC
Engine Package Weights
 131 Jab 2200, 161 Jab 3300 140 Jab 2200, 170 Jab 3300
2.12.07 SNX-P10 A Detail A "…Engine Mount Cushion Set Supplied with Jabiru Engine" "…ACV-J01-10 Shock Mounts for Jabiru Engine"
10.2.09 SNX-P10 A Detail B-B Throttle and Mixture cable call-outs incorrect Refer to engine and/or Aerocarb manual for proper throttle cable options.
12.1.03 SNX-P11 A
-01 Motor Mount Installation
--
 Remove Material from F15-02R/L to clear motor mount.
2.12.07 SNX-P11 B -01 Motor Mount Installation AN960-4 Washer 8 Required on -01 AN960-416 Washer 8 Required on -01
2.12.07 SNX-P12 B -01 Motor Mount Installation AN960-4 Washer 8 Required on -01 AN960-416 Washer 8 Required on -01
10.4.07 SNX-P13 C Detail -13 Hinge Half 4 1/2" Long 3 1/2" Long
2.12.07 SNX-P16 A Detail -02 -- Delete -02 Cowling w/bumps, replace with -03 Universal Cowling
12.1.03 SNX-P20 A
-01 and -02 installations
 Earl's Cooler 21903 B&M Cooler 130-70265 (www.jegs.com)
2.12.07 SNX-P20 A Detail A "…Engine Mount Cushion Set Supplied with Jabiru Engine" "…ACV-J01-10 Shock Mounts for Jabiru Engine"
10.2.09 SNX-P20 B Detail B-B Throttle and Mixture cable call-outs incorrect Refer to engine and/or Aerocarb manual for proper throttle cable options.
12.1.03 SNX-P21 A
-01 Motor Mount Installation
--
 Remove Material from F15-02R/L to clear motor mount.
2.12.07 SNX-P21 B -01 Motor Mount Installation AN960-4 Washer 8 Required on -01 AN960-416 Washer 8 Required on -01
2.12.07 SNX-P22 NC -01 Motor Mount Installation AN960-4 Washer 8 Required on -01 AN960-416 Washer 8 Required on -01
2.12.07 SNX-P30 A Detail A Automotive Shock Absorber NAPA #650-1151 ACV-P01-19 Rubber Shock Mounts
10.2.09 SNX-P30 A Detail B-B Throttle and Mixture cable call-outs incorrect Refer to engine and/or Aerocarb manual for proper throttle cable options.
12.1.03 SNX-P31 NC
-01 Motor Mount Installation
--
 Remove Material from F15-02R/L to clear motor mount.
12.2.02 SNX-P31 NC
Detail -01
 Isometric shows cross-tubes to lower mounts 3-View shows cross-tubes to upper mounts. This is correct.
2.12.07 SNX-P31 A -01 Motor Mount Installation AN960-4 Washer 8 Required on -01 AN960-416 Washer 8 Required on -01
2.12.07 SNX-P32 NC -01 Motor Mount Installation AN960-4 Washer 8 Required on -01 AN960-416 Washer 8 Required on -01
3.24.11 SNX-T01 A -01 and -03 Fiberglass tips not depicted Added fiberglass tips
2.12.07 SNX-T02 B Section E-E 9 Spaces @ 1 1/16" [25.3 mm] 9 Spaces @ 1 1/16" [27.0 mm] Center to Center Spacing
3.24.11 SNX-T02 B Section B-B -- Trim Tab not required if Dial-A-Speed trim (AeroConversions Trim System) is installed.
3.24.11 SNX-T02 B -02 Installing rivets through skins and T04-05 tip ribs. Rivets through tip ribs not installed at this time. Rivets are installed on SNX-T14.
3.24.11 SNX-T02 B Next Assembly Block Next Assembly has no entry Next Assembly should be SNX-T14
2.17.11 SNX-T03 NC -05 Assembly SNX-T06-03 incorrectly depicted with solid line on rear view SNX-T06-03 correctly depicted with hidden line on rear view
2.12.07 SNX-T04 NC Detail -05 Tip Rib -- If fiberglass tail tips are installed, remove the tab on the leading edge before installing.
12.2.02 SNX-T06 --
Detail -02
 CCP-42 Flush Blind Rivets 14 req'd and 17 req'd CCP-42 Blind Rivets 14 req'd and 17 req'd
2.25.09 SNX-T07 B Detail -05 Trim Tab MS20257P1 Hinge MS20257P3 Hinge
3.24.11 SNX-T08 NC -01 Installing rivets through skins and T10-04 tip ribs. Rivets through tip ribs not installed at this time. Rivets are installed on SNX-T14.
3.24.11 SNX-T08 NC Next Assembly Block Next Assembly for -01 was SNX-T01 Next Assembly for -01 should be SNX-T14
9.3.09 SNX-T09 NC Section A-A Main Spar Forward Strap incorrectly labeled "SNX-T12-01" SNX-T12-02 Main Spar Forward Strap
2.12.07 SNX-T10 NC Detail -04 Tib Rib -- If fiberglass tail tips are installed, remove the tab on the leading edge before installing.
2.12.07 SNX-T12 NC Detail -01 3/32" Pilot Holes Typical 40 places 3/32" Pilot Holes Typical 38 places
12.1.03 SNX-T13 NC
Rudder Skin
 Solid Line on main (Left Side) View Dashed (Phantom) Line on Main (Left Side) View
2.12.07 SNX-T14 NC General Note -- Remove Optional from Title Block and all notes
3.24.11 SNX-T14 NC Detail A -- Install CCP-42 rivets to secure tail tips
12.6.04 SNX-W02 NC
Detail F
 File/Sand Thrust Bearing Thickness as required File/Sand Thrust Bearing Length as required
12.2.02 SNX-W03 D
Detail -01R, -01L
 Center Rib Call-out, W04-03 and W04-02 are Reversed
--
12.2.02 SNX-W03 D
Assembly -03
 Rib Call-out W04-02 and W04-03 are Reversed
--
01.28.10 SNX-W03 D Detail -03 Hinge Half Detail -03 Hinge Half Should be: Detail -02 Hinge Half
12.6.04 SNX-W05 NC
-01R/L
 4 pilot holes on one W06-02 Rib Installation 4 Pilot holes should be shown as 4 rivets installed
2.12.07 SNX-W07 A -01R/L -- Add Note: Building a flat wing is critical in this procedure. Ref the Wing Squaring/Skinning Instructions Located on our Instruction Sheets Page
2.12.07 SNX-W07 A -01R/L -- Add Note: Drill holes in leading edges for CCC-42 with a #32 Drill then dimple
2.12.07 SNX-W08 B Detail E AN3-7A Bolt…Install from Forward Side AN3-7A Bolt…Install from Aft Side. See linked file: SNXW08c-Detail-E.jpg
8.12.08 SNX-W08 C Details A and E 2 rivets securing SNX-W11-06 not identified Replaced rivets with bolts and screws as shown on linked files: SNXW08c-Detail-A.jpg; SNXW08c-Detail-E.jpg
10.4.07 SNX-W10 B Detail B 2nd hole down on LH Side not dimensioned (appears to be 5/8") Locate 2nd hole down (fuselage attach hole) is 37/64" [14.58mm] from the left edge.
2.12.07 SNX-W11 A -01 Lower Angle -- Add Overall Dimension of 23 5/32"
12.1.03 SNX-W12 B
-02R/L, -03R/L
 SNX-Z01-01 SNX-Z01-02
12.6.04 SNX-W12 C -02R/L, -03R/L -- Add note for kit builders: Pilot holes for rib attach points must be drilled accurately. Use a formed rib as a pattern.
12.6.04 SNX-W12 C Details D and G AN3-7, 2 places AN3-7A, 2 places
10.4.07 SNX-W13 NC -02R/L Drawing Error only- Bottom View is not properly depicted All dimensions are correct. Bottom view should show sides extending beyond the bottom flange.
2.12.07 SNX-W15 B Detail -08, -09 -- Replace Gusset Stock Blank Size w/Laser-Cut Gusset Stock SNX-W15-08
2.12.07 SNX-W15 B Details -01, -02, -03, -04, -06 -- Kit Builders Modify -06 view to use laser-cut Gusset Stock SNX-W15-08 on top and bottom.
2.12.07 SNX-W16 A Detail -07, -08 -- Replace Gusset Stock Blanks with laser-cut blanks SNX-W16-07 and SNX-W16-08
3.2.11 SNX-W21 NC -10 Bellcrank Assembly -- Added note to tighten nut to lock bushings against bellcrank.
3.2.11 SNX-W21 NC -11 Bellcrank Hole Diameter missing 3/16" diameter holes, 3 places.
3.2.11 SNX-W21 NC -12 Bushings "Epoxy Prime" "Lubricate with White Lithium Grease"
12.6.04 SNX-W23 NC
Detail -04
--
 Premade Pitot-static assembly available as an alternative from Aircraft Spruce, P/N 15144.
2.12.07 SNX-W23 NC View of Bottom of RH Wing 3/8" O.D. x 1/4" I.D. x 66" [168mm] Long Tygon Tubing 3/8" O.D. x 1/4" I.D. x 66" [1677mm] Long Tygon Tubing
11.12.08 SNX-W24, 25, 26, 27 NC -- -- Optional Sport Acro Aileron Installation: If not included in your plans, these drawings are available upon request: tech@sonexaircraft.com
1.6.09 SNX-W25 NC Detail of Aileron Balancing Delete this Detail Balance Sport Acro Aileron with 1/2 of the supplied Counterweight (Sonex P/N SNX-W04-08). All flight testing has been conducted using the same counterweight as the standard Sonex Aileron.
12.6.04 SNX-Z01 A
-03 Angle usage table
 SNX-F10 Qty 40" Delete call out for SNX-F10 Qty 40"

 
Click to verify BBB accreditation and to see a BBB report.

| Home | Choosing Sonex | Company | Kits | Support | Builder Network | Sport Pilot | Ordering | Press Room |

© Copyright 2011 Sonex Aircraft, LLC -- All Rights Reserved | Contact Sonex HR

Subscribe to Sonex and AeroConversions Mailing Lists and News Feeds