Sonex -- The Sport Aircraft Reality Check!

Sonex Seat Modification: Last Updated Nov. 21, 2005

Modified Part List:

Part Number

Description

Change for Lowered Seat

SNX-C05-02

Control Stick Frame Assembly

Add 1/8" thick Vertical Piece 1/8" offset from Centerline of Part and Tab on Upper RH side of Part for Optional Trim System Attachment. Becomes Part Number SNX-C05-08 [Existing parts can be modified if returned to Sonex,ltd. Cost is $50]

SNX-C05-04

Seat Sling

Dimension Changes: WAS: 19 5/32" [486.4 mm], IS: 18 7/32" [462.8 mm]; WAS: 17 45/64"[449.6 mm] IS: 19 1/4" [489 mm] Center Cut-out Changes: WAS: 3/8"[9.5 mm] IS: 1 1/2"[38.1 mm]; WAS: 5 1/2" [139.7 mm] IS: 8 1/2"[215.9 mm] with 3/4" Radius. Becomes Part Number SNX-C05-09

SNX-F03-01

Rear Spar Carry Through Assembly

Pictoral Change Only: Move Hole to Centerline

SNX-F03-02

Channel

Move 1 3/4" diameter hole to the Centerline of the Part. WAS: 16 3/16" [410.9 mm] IS: 19 35/64" [496.6 mm]

SNX-F09-02

Seat Belt Attach Assembly

Move SNX-F10-05R and -05L further away from each other. WAS:19 3/32" [485.1 mm] IS:18 15/32" [469.1 mm]; WAS: 1/2" [12.7 mm] IS: 1 3/4" [44.5 mm]. Move SNX-F10-07R and -07L closer to Centerline. Keep 9/16" spacing and locate parts 7/32" [5.6 mm] on one side of the Centerline.

SNX-F09

View A-A

Move SNX-F10-16 per F09-02 dimensions (offset from centerline 7/32" [5.6 mm]). Pictoral Changes: Swap SNX-F10-13R and -13L and move SNX-F10-05R and -05L per F09-02 dimensions.

SNX-F09

View B-B

Move rivet attach holes for SNX-F10-16 per F09-02 dimensions (offset from centerline 7/32" [5.6 mm])

SNX-F09

View C-C

Pictoral Changes: Move hole cutout to the Centerline; Move SNX-F10-07R and -07L offset from centerline 7/32"; Move SNX-F10-05R and -05L further away from each other (1 1/4" spacing)

SNX-F09

View G-G

Pictoral Change: Swap SNX-F10-13R and -13L

SNX-F09

Detail J

Pictoral Change: Swap SNX-F10-13R and -13L

SNX-F09

View L-L

Pictoral Change: Hidden Lines on Seat Belt Attach Bracket become solid lines as bracket is moved outboard of SNX-F10-13R and -13L

SNX-F10-01

Angle

Move 5/8" Radius Cutout to Centerline

SNX-F10-03

Angle

Make from 1"x1"x0.125" thick 6061-T6 Aluminum Angle instead of SNX-Z02-03 Angle Stock. Move 5/8" Radius Cutout to Centerline; Turn piano hinge around. Align hingle with opposite edge of Angle.

SNX-F21

View N-N

Move F23-11 to Centerline

SNX-F21

View P-P

Move F23-09 to Centerline

New Part List:

Part Number

Description

Change for Lowered Seat

SNX-C06-04

Idler Push Rod Cover

Make from 0.025" thick 6061-T6 Aluminum. Blank Size: 8 1/2" [215.9 mm] x 4 15/32" [113.5 mm]. Section Dimensions 1/2" Flange on both sides, 3/4" straight, 3/4" radius cap. [Part Number XNS-Z04-01 Hat Section]

Back to Drawing Revisions Page